SWITCHES

Showing 205–216 of 231 results

VC-234
Cost-Effective VDSL2 Profile 17a/30a CO / CPE bridge solution
• One box design, CO / CPE selectable via DIP Switch
• Defines symmetric band plan for the transmission of upstream
and downstream signals
• Complies with IEEE 802.3, 10Base-T, IEEE 802.3u, 100Base-TX
and IEEE 802.3x, Flow control Ethernet standards
• DMT (Discrete Multi-Tone) line coding
• Half duplex Back pressure and IEEE 802.3x Full Duplex Pause
frame flow control
• Built-in POTS splitter to share voice and data
• Two RJ-11 connectors for each VDSL port, one for VDSL
connection and one for POTS connection
• Voice and data communication can be shared simultaneously
based on the existing telephone wire
• Four 10/100Mbps RJ-45 port, Auto-Negotiation and Auto-MDI/
MDI-X
• Supports up to 1536 bytes packet size, IEEE 802.1Q VLAN tag
transparent
• Hardware IGMP Snooping for Multimedia service
• VDSL2 stand-alone transceiver for simple bridge modem
application
• Advantage of minimum installation time (Simply as Plug-andPlay)
• Selectable target profile and target SNR margin
• Supports extensive LED indicators for network diagnosis
Comparer
Vue Rapide
VC-234G
ITU-T G.993.5 G.Vector and G.INP
• DMT-based coding technology
• Built-in POST splitter to share voice and date
• One RJ11 connector for VDSL port with VDSL connection
• One phone connector for telephone connection
• Voice and data communication can be shared
simultaneously based on the existing telephone wire
• CO/CPE mode selectable via DIP switch
• Selectable target band plan and SNR margin
• Up to 200/100Mbps (G.INP, Asym, 8dB) bandwidth
• 4 10/100/1000BASE-TX LAN ports
• Complies with IEEE 802.3, 10BASE-T, IEEE 802.3u,
100BASE-TX and IEEE 802.3x, flow control Ethernet
standards
• Half duplex back pressure and IEEE 802.3x full duplex
pause frame flow control
• Supports IEEE 802.1Q VLAN tag transparency
• VDSL2 stand-alone transceiver for simple bridge modem
application
• Advantage of minimum installation time (Simply Plug-andPlay)
• Supports extensive LED indicators for network diagnosis
• Compact in size and easy to install
Comparer
Vue Rapide
VGW-1620FS
• IETF SIP RFC3261 based on UDP/TCP/TLS
• 16-line FXS connects to analog phone set or PABX
• Fax over T.38 and Pass-through
• ITU-T G.711 A-law, G.711 μ-law, G.723.1 and G.729
voice coding
• In-band / out of band DTMF (RFC4733, RFC2833 / SIP
INFO)
• Echo cancellation exceeding ITU-T G.168, up to 128ms
tail length
• Supports SIP Trunk and Caller ID: DTMF/FSK CLI
Presentation
Internet Features
• Supports SNMP v1/v2/v3
• Supports VLAN 802.1P and 802.1Q
• Supports Layer3 QoS and DiffServ
• Supports STUN (RFC 3489) and Outbound Proxy
• Supports TR069 and Auto Provisioning
• Supports TLS/SRTP Security
Call Features
• Call waiting, transfer (Blind transfer, Attend transfer)
• Call hold, quick pick
• Call forwarding unconditional
• Call forwarding on no reply
• Hotline, speed dial, direct IP call
• Do not disturb (DND), 3-way conferencing
Comparer
Vue Rapide
VGW-820FS
IETF SIP RFC3261 based on UDP/TCP/TLS
• 8-line FXS connects to analog phone set or PABX
• Fax over T.38 and Pass-through
• ITU-T G.711 A-law, G.711 μ-law, G.723.1 and G.729 voice
coding
• In-band/out of band DTMF (RFC4733, RFC2833/SIP INFO)
• Echo cancellation exceeding ITU-T G.168, up to 128ms tail
length
• Supports SIP Trunk and Caller ID: DTMF/FSK CLI
Presentation
Internet Features
• Supports SNMP v1/v2/v3
• Supports VLAN 802.1P and 802.1Q
• Supports Layer 3 QoS and DiffServ
• Supports STUN (RFC 3489) and Outbound Proxy
• Supports TR069 and Auto Provisioning
• Supports TLS/SRTP Security
Call Features
• Call waiting/transfer (Blind transfer, Attend transfer)
• Call hold/Quick pick
• Call Forwarding Unconditional
• Call Forwarding on No Reply
• Hotline/Speed Dial/Direct IP Call
• Do Not Disturb (DND)/Three-way conferencing
Comparer
Vue Rapide
WGSW-20160HP
WGSW-20160HP
Physical Port
16-port 10/100/1000BASE-T RJ45 copper with 802.3at PoE+ injector function
4 10/100/1000Mbps TP and SFP shared combo interfaces, supporting 100/1000Mbps dual mode, shared with Ports 17 to 20
RS232 RJ45 console interface for switch basic management and setup
Comparer
Vue Rapide
WGSW-24040
WGSW-24040 pinet Physical Ports
24 10/100/1000BASE-T RJ45 copper ports
4 100/1000BASE-X /SFP slots, shared with Port-21 to Port-24
Console interface for basic management and setup
Comparer
Vue Rapide
WGSW-24040HP4
WGSW-24040HP4
Physical Port
24-port 10/100/1000BASE-T RJ45 copper with 802.3at PoE+ injector function
4 100/1000BASE-X mini-GBIC/SFP slots, shared with port-21 to port-24
RS232 RJ45 console interface for switch basic management and setup
Comparer
Vue Rapide
WGSW-24040R
Physical Ports
24 10/100/1000BASE-T RJ45 copper ports
4 100/1000BASE-X /SFP slots, shared with Port-21 to Port-24
Console interface for basic management and setup
Comparer
Vue Rapide
WS-1032P
Physical Port
8-port 10/100/1000BASE-T with 36W PoE injector
2-port 1/2.5/10GBASE-X SFP+
RS232 RJ45 console interface for switch basic management and setup

Wireless LAN AP Management
Dashboard: provides at-a-glance view of system and wireless network status
AP Discovery: one key to discover the managed APs on the managed LAN
Customized Profile: allows multiple wireless profiles creation and maintenance
Auto Provision: multi-AP provisioning with one click
Cluster Management: simplifies high-density AP management
Zone Plan: optimizes AP deployment with actual signal coverage
Analysis: real-time AP status monitoring
Scalability: free system upgrade and AP firmware bulk upgrade capability

Power over Ethernet
Up to 8 ports of IEEE 802.3af/802.3at devices powered
Supports PoE Power up to 36 watts for each PoE port
Auto detects powered device (PD)
Circuit protection prevents power interference between ports
Remote power feeding up to 100 meters
PoE management features
Total PoE power budget control
Per port PoE function enable/disable
PoE admin-mode control
PoE port power feeding priority
Per PoE port power limit
PD classification detection
Intelligent PoE features
Temperature threshold control
PoE usage threshold control
PD alive check
PoE schedule

Layer 3 IP Routing Features
IP dynamic routing protocol supports RIPv2, OSPFv2 and OSPFv3
IPv4/IPv6 hardware static routing
Routing interface provides per VLAN routing mode

Layer2 Features
High performance of Store-and-Forward architecture and runt/CRC filtering eliminates erroneous packets to optimize the network bandwidth
Storm Control support
Broadcast/Multicast/Unknown unicast
Supports VLAN
IEEE 802.1Q tagged VLAN
Supports provider bridging (VLAN Q-in-Q, IEEE 802.1ad)
Private VLAN Edge (PVE)
Protocol-based VLAN
MAC-based VLAN
Voice VLAN
GVRP(GARP VLAN Registration Protocol)
Supports Spanning Tree Protocol
STP, IEEE 802.1D Spanning Tree Protocol
RSTP, IEEE 802.1w Rapid Spanning Tree Protocol
MSTP, IEEE 802.1s Multiple Spanning Tree Protocol, spanning tree by VLAN
BPDU Guard
Supports Link Aggregation
802.3ad Link Aggregation Control Protocol(LACP)
Cisco ether-channel (static trunk)
Maximum 5 trunk groups, up to 10 ports per trunk group
Up to 56Gbps bandwidth (full duplex mode)
Provide sport mirror (many-to-1)
Port mirroring to monitor the incoming or outgoing traffic on a particular port
Loop protection to avoid broadcast loops
Link Layer Discovery Protocol (LLDP)
Compatible with Cisco uni-directional link detection (UDLD) that monitors a link between two switches and blocks the ports on both ends of the link if the link fails at any point between the two devices
Supports G.8032 ERPS (Ethernet Ring Protection Switching)

Quality of Service
Ingress Shaper and Egress Rate Limit per port bandwidth control
8 priority queues on all switch ports
Traffic classification
IEEE 802.1p CoS
TOS/DSCP/IP Precedence of IPv4/IPv6 packets
IP TCP/UDP port number
Typical network application
Strict priority and Weighted Round Robin (WRR) CoS policies
Supports QoS and In/Out bandwidth control on each port
Traffic-policing policies on the switch port
DSCP remarking

Multicast
Supports IPv4 IGMP Snooping v1, v2 and v3
Supports IPv6 MLD Snooping v1 and v2
Querier mode support
IGMP Snooping port filtering
MLD Snooping port filtering
Multicast VLAN Registration (MVR) support

Security
Authentication
IEEE 802.1x Port-based/MAC-based network access authentication
Built-in RADIUS client to co-operate with the RADIUS servers
TACACS+ login users access authentication
RADIUS/TACACS+ users access authentication
Access Control List
IP-based Access Control List (ACL)
MAC-based Access Control List
Source MAC/IP address binding
DHCP Snooping to filter un-trusted DHCP messages
Dynamic ARP Inspection discards ARP packets with invalid MAC address to IP address binding
IP Source Guard prevents IP spoofing attacks
Auto DoS rule to defend DoS attack
IP address access management to prevent unauthorized intruder

Management
IPv4 and IPv6 dual stack management
Switch Management Interfaces
Console/Telnet Command Line Interface
Web switch management
SNMP v1, v2c, and v3 switch management
SSHv2, TLSv1.2 secure access
IPv6 IP Address/NTP/DNS management
Built-in Trivial File Transfer Protocol (TFTP) client
BOOTP and DHCP for IP address assignment
System Maintenance
Firmware upload/download via HTTP/TFTP
Reset button for system reboot or reset to factory default
Dual Images
DHCP Relay
DHCP Option82
User Privilege levels control
NTP (Network Time Protocol)
Link Layer Discovery Protocol (LLDP) and LLDP-MED
Network Diagnostic
SFP-DDM (Digital Diagnostic Monitor)
ICMPv6/ICMPv4 Remote Ping
Cable Diagnostic technology provides the mechanism to detect and report potential cabling issues
SMTP/Syslog remote alarm
Four RMON groups (history, statistics, alarms and events)
SNMP trap for interface Linkup and Linkdown notification
System Log
PLANET Smart Discovery Utility for deployment management
PLANET UNI-NMS (Universal Network Management) and Smart Discovery Utility for deployment management
Ordering Information
WS-1032P
Wireless AP Managed Switch with 8-Port 802.3at PoE + 2-Port 10G SFP+
Comparer
Vue Rapide
WS-1032P (Copie)
Physical Port
8-port 10/100/1000BASE-T with 36W PoE injector
2-port 1/2.5/10GBASE-X SFP+
RS232 RJ45 console interface for switch basic management and setup

Wireless LAN AP Management
Dashboard: provides at-a-glance view of system and wireless network status
AP Discovery: one key to discover the managed APs on the managed LAN
Customized Profile: allows multiple wireless profiles creation and maintenance
Auto Provision: multi-AP provisioning with one click
Cluster Management: simplifies high-density AP management
Zone Plan: optimizes AP deployment with actual signal coverage
Analysis: real-time AP status monitoring
Scalability: free system upgrade and AP firmware bulk upgrade capability

Power over Ethernet
Up to 8 ports of IEEE 802.3af/802.3at devices powered
Supports PoE Power up to 36 watts for each PoE port
Auto detects powered device (PD)
Circuit protection prevents power interference between ports
Remote power feeding up to 100 meters
PoE management features
Total PoE power budget control
Per port PoE function enable/disable
PoE admin-mode control
PoE port power feeding priority
Per PoE port power limit
PD classification detection
Intelligent PoE features
Temperature threshold control
PoE usage threshold control
PD alive check
PoE schedule

Layer 3 IP Routing Features
IP dynamic routing protocol supports RIPv2, OSPFv2 and OSPFv3
IPv4/IPv6 hardware static routing
Routing interface provides per VLAN routing mode

Layer2 Features
High performance of Store-and-Forward architecture and runt/CRC filtering eliminates erroneous packets to optimize the network bandwidth
Storm Control support
Broadcast/Multicast/Unknown unicast
Supports VLAN
IEEE 802.1Q tagged VLAN
Supports provider bridging (VLAN Q-in-Q, IEEE 802.1ad)
Private VLAN Edge (PVE)
Protocol-based VLAN
MAC-based VLAN
Voice VLAN
GVRP(GARP VLAN Registration Protocol)
Supports Spanning Tree Protocol
STP, IEEE 802.1D Spanning Tree Protocol
RSTP, IEEE 802.1w Rapid Spanning Tree Protocol
MSTP, IEEE 802.1s Multiple Spanning Tree Protocol, spanning tree by VLAN
BPDU Guard
Supports Link Aggregation
802.3ad Link Aggregation Control Protocol(LACP)
Cisco ether-channel (static trunk)
Maximum 5 trunk groups, up to 10 ports per trunk group
Up to 56Gbps bandwidth (full duplex mode)
Provide sport mirror (many-to-1)
Port mirroring to monitor the incoming or outgoing traffic on a particular port
Loop protection to avoid broadcast loops
Link Layer Discovery Protocol (LLDP)
Compatible with Cisco uni-directional link detection (UDLD) that monitors a link between two switches and blocks the ports on both ends of the link if the link fails at any point between the two devices
Supports G.8032 ERPS (Ethernet Ring Protection Switching)

Quality of Service
Ingress Shaper and Egress Rate Limit per port bandwidth control
8 priority queues on all switch ports
Traffic classification
IEEE 802.1p CoS
TOS/DSCP/IP Precedence of IPv4/IPv6 packets
IP TCP/UDP port number
Typical network application
Strict priority and Weighted Round Robin (WRR) CoS policies
Supports QoS and In/Out bandwidth control on each port
Traffic-policing policies on the switch port
DSCP remarking

Multicast
Supports IPv4 IGMP Snooping v1, v2 and v3
Supports IPv6 MLD Snooping v1 and v2
Querier mode support
IGMP Snooping port filtering
MLD Snooping port filtering
Multicast VLAN Registration (MVR) support

Security
Authentication
IEEE 802.1x Port-based/MAC-based network access authentication
Built-in RADIUS client to co-operate with the RADIUS servers
TACACS+ login users access authentication
RADIUS/TACACS+ users access authentication
Access Control List
IP-based Access Control List (ACL)
MAC-based Access Control List
Source MAC/IP address binding
DHCP Snooping to filter un-trusted DHCP messages
Dynamic ARP Inspection discards ARP packets with invalid MAC address to IP address binding
IP Source Guard prevents IP spoofing attacks
Auto DoS rule to defend DoS attack
IP address access management to prevent unauthorized intruder

Management
IPv4 and IPv6 dual stack management
Switch Management Interfaces
Console/Telnet Command Line Interface
Web switch management
SNMP v1, v2c, and v3 switch management
SSHv2, TLSv1.2 secure access
IPv6 IP Address/NTP/DNS management
Built-in Trivial File Transfer Protocol (TFTP) client
BOOTP and DHCP for IP address assignment
System Maintenance
Firmware upload/download via HTTP/TFTP
Reset button for system reboot or reset to factory default
Dual Images
DHCP Relay
DHCP Option82
User Privilege levels control
NTP (Network Time Protocol)
Link Layer Discovery Protocol (LLDP) and LLDP-MED
Network Diagnostic
SFP-DDM (Digital Diagnostic Monitor)
ICMPv6/ICMPv4 Remote Ping
Cable Diagnostic technology provides the mechanism to detect and report potential cabling issues
SMTP/Syslog remote alarm
Four RMON groups (history, statistics, alarms and events)
SNMP trap for interface Linkup and Linkdown notification
System Log
PLANET Smart Discovery Utility for deployment management
PLANET UNI-NMS (Universal Network Management) and Smart Discovery Utility for deployment management
Ordering Information
WS-1032P
Wireless AP Managed Switch with 8-Port 802.3at PoE + 2-Port 10G SFP+
Comparer
Vue Rapide
WS-2864PVR
Physical Port
24 10/100/1000BASE-T Gigabit RJ45 copper ports with 24-port IEEE 802.3af/at PoE+ injector function
4 10GBASE-SR/LR SFP+ slots, compatible with 1000BASE-SX/LX/BX and 2500BASE-X SFP
RS232 RJ45 console interface for switch basic management and setup

Wireless LAN AP Management
Dashboard: provides at-a-glance view of system and wireless network status
AP Discovery: one key to discover the managed APs on the managed LAN
Customized Profile: allows multiple wireless profiles creation and maintenance
Auto Provision: multi-AP provisioning with one click
Cluster Management: simplifies high-density AP management
Zone Plan: optimizes AP deployment with actual signal coverage
Analysis: real-time AP status monitoring
Scalability: free system upgrade and AP firmware bulk upgrade capability

Power over Ethernet
Up to 24 ports of IEEE 802.3af/802.3at devices powered
Supports PoE Power up to 36 watts for each PoE port
Auto detects powered device (PD)
Circuit protection prevents power interference between ports
Remote power feeding up to 100 meters
PoE management
Total PoE power budget control
Per port PoE function enable/disable
PoE admin-mode control
PoE port power feeding priority
Per PoE port power limitation
PD classification detection
PoE extend mode control to support power feeding up to a distance of up to 200 meters
Intelligent PoE features
Temperature threshold control
PD alive check
PoE schedule
PD scheduled power-recycle

Layer 2 Features
Prevents packet loss with back pressure (half-duplex) and IEEE 802.3x pause frame flow control (full-duplex)
High performance of Store-and-Forward architecture and runt/CRC filtering eliminates erroneous packets to optimize the network bandwidth
Storm Control support
Broadcast/Multicast/Unknown unicast
Supports VLAN
IEEE 802.1Q tagged VLAN
Supports provider bridging (VLAN Q-in-Q, IEEE 802.1ad)
Private VLAN Edge (PVE)
Protocol-based VLAN
MAC-based VLAN
Voice VLAN
Supports Spanning Tree Protocol
IEEE 802.1D Spanning Tree Protocol
IEEE 802.1w Rapid Spanning Tree Protocol
IEEE 802.1s Multiple Spanning Tree Protocol, spanning tree by VLAN
BPDU Guard
Supports Link Aggregation
802.3ad Link Aggregation Control Protocol (LACP)
Cisco ether-channel (static trunk)
Maximum 14 trunk groups, up to 4 ports per trunk group
Up to 80Gbps bandwidth (full duplex mode)
Provides port mirror (many-to-1)
Port mirroring to monitor the incoming or outgoing traffic on a particular port
Loop protection to avoid broadcast loops
Supports ERPS (Ethernet Ring Protection Switching)
Compatible with Cisco uni-directional link detection(UDLD) that monitors a link between two switches and blocks the ports on both ends of the link if the link fails at any point between the two devices
Link Layer Discovery Protocol (LLDP)

Layer 3 IP Routing Features
Supports maximum 128 static routes and route summarization
IP dynamic routing protocol supports OSPFv2
Routing interface provides per VLAN routing mode

Quality of Service
Ingress Shaper and Egress Rate Limit per port bandwidth control
8 priority queues on all switch ports
Traffic classification
IEEE 802.1p CoS
TOS/DSCP/IP Precedence of IPv4/IPv6 packets
IP TCP/UDP port number
Typical network application
Strict priority and Weighted Round Robin (WRR) CoS policies
Supports QoS and In/Out bandwidth control on each port
Traffic policing on the switch port
DSCP remarking

Multicast
Supports IPv4 IGMP Snooping v1, v2 and v3
Supports IPv6 MLD Snooping v1 and v2
Querier mode support
IGMP Snooping port filtering
MLD Snooping port filtering
Multicast VLAN Registration (MVR) support

Security
Authentication
IEEE 802.1x Port-based/MAC-based network access authentication
Built-in RADIUS client to co-operate with the RADIUS servers
TACACS+ login users access authentication
RADIUS/TACACS+ users access authentication
Access Control List
IP-based Access Control List (ACL)
MAC-based Access Control List
Source MAC/IP address binding
DHCP Snooping to filter untrusted DHCP messages
Dynamic ARP Inspection discards ARP packets with invalid MAC address to IP address binding
IP Source Guard prevents IP spoofing attacks
Auto DoS rule to defend DoS attack
IP address access management to prevent unauthorized intruder

Management
IPv4 and IPv6 dual stack management
Switch Management Interfaces
Console/Telnet Command Line Interface
2.4” inch LCD touch screen
Web switch management
SNMP v1 and v2c switch management
SSHv2, TLSv1.2 and SNMPv3 secure access
SNMP Management
Four RMON groups (history, statistics, alarms and events)
SNMP trap for interface Link Up and Link Down notification
IPv6 IP Address/NTP/DNS management
Built-in Trivial File Transfer Protocol (TFTP) client
BOOTP and DHCP for IP address assignment
System Maintenance
Firmware upload/download via HTTP/TFTP
Reset button for system reboot or reset to factory default
Dual Images
DHCP Relay
DHCP Option82
User Privilege levels control
NTP (Network Time Protocol)
Link Layer Discovery Protocol (LLDP) and LLDP-MED
Network Diagnostic
SFP-DDM (Digital Diagnostic Monitor)
ICMPv6/ICMPv4 Remote Ping
Cable Diagnostic technology provides the mechanism to detect and report potential cabling issues
SMTP/Syslog remote alarm
System Log
PLANET Smart Discovery Utility for deployment management
PLANET UNI-NMS (Universal Network Management) and Smart Discovery Utility for deployment management
Ordering Information
WS-2864PVR
Wireless AP Managed Switch with 24-Port 802.3at PoE + 4-Port 10G SFP+ + LCD Touch Screen and 48VDC Redundant Power
Comparer
Vue Rapide

Ordering Information
WS-1032P	Wireless AP Managed Switch with 8-Port 802.3at PoE + 2-Port 10G SFP+

Ordering Information
WS-1032P	Wireless AP Managed Switch with 8-Port 802.3at PoE + 2-Port 10G SFP+

Ordering Information
WS-2864PVR	Wireless AP Managed Switch with 24-Port 802.3at PoE + 4-Port 10G SFP+ + LCD Touch Screen and 48VDC Redundant Power

WS-C2960C-8PC-L

Product Code	WS-C2960C-8PC-L
Feature Set	LAN Base
Uplink Interfaces	2 x 1G copper or 2 x 1G SFP
Ports	8 x 10/100 Fast Ethernet
Available POE Power	124W
Forwarding Bandwidth	10 Gbps
RAM	128 MB
Flash Memory	64 MB
Dimensions	4.6 x 26.9 x 23.9 cm
Package Weight	4.38 Kg

Comparer

Vue Rapide

SWITCHES

VC-234

VC-234G

VGW-1620FS

VGW-820FS

WGSW-20160HP

WGSW-20160HP

WGSW-24040

WGSW-24040HP4

WGSW-24040HP4

WGSW-24040R

WS-1032P

WS-1032P

WS-1032P (Copie)

WS-1032P

WS-2864PVR

WS-2864PVR

WS-C2960C-8PC-L